Saturday, September 3, 2011

Canon Copier error errors code codes imagerunner copiers copy machine copy machines


IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->




BRAND		MODELERROR CODEMOST LIKELY CAUSE
CANON155E0The fusing unit does not heat up
CANON155E1The sensor motor or sensor, the DC controller on the main board DC controller
CANON155E2The copyboard position sensor
CANON155E4Main motor, Main motor PCB, DC controller
CANON155E5Lens home position error
CANON155E6Exposure lamp control PCB, light intensity error, DC controller
CANON155E7Main motor PCB, DC controller
CANON155E8Counter error
CANON155E9AC drive board, DC controller
CANON155ECCopy board drive lock
CANON155EDOperation panel
CANON155EEMain motor drive board, DC drive board
CANONFC330E0The fusing unit does not heat up
CANONFC330E1Fusing film damaged or out of position
CANONFC330E2Copy board drive lock or home position error
CANONFC330E6Blown exposure lamp or exposure lamp terminals bad contact
CANON720, 740, 750, 770CFusing film damaged or out of position the machine tries to compensate
CANON720, 740, 750, 770HFusing unit overheating
CANON720, 740, 750, 770E0The machine was switched OFF and ON after one of the E00X error codes
CANON720, 740, 750, 770E000Bad thermistor, thermofuse, fusing element, triac or power supply
CANON720, 740, 750, 770E001Bad thermistor, triac or power supply
CANON720, 740, 750, 770E002bad thermistor, thermofuse, fusing element, triac or power supply
CANON720, 740, 750, 770E003bad thermistor, thermofuse, fusing element, triac or power supply
CANON720, 740, 750, 770E007fusing film damaged or out of position
CANON720, 740, 750, 770E010main motor lock, DC power supply
CANON720, 740, 750, 770E064Main power supply or Main PCB
CANON720, 740, 750, 770E202scanner home position not found
CANON720, 740, 750, 770E210lens home position not found
CANON720, 740, 750, 770E220exposure lamp, exposure control PCB, light intensity error, main PCB
CANON720, 740, 750, 770E240DC power source controller or main power supply
CANON720, 740, 750, 770E261frequency error caused by the main power supply or the power outlet
CANON720, 740, 750, 770E803main board, main power supply or fusing lamp defective
CANONNP1010, NP1020E000Bad thermistor, thermofuse, fusing element, triac or power supply
CANONNP1010, NP1020E001Bad thermistor, triac or power supply
CANONNP1010, NP1020E010main motor lock, main motor rotation sensor,main board
CANONNP1010, NP1020E210lens or scanner home position not found
CANON2020, 2120E000cuptorul nu se incalzeste
CANON2020, 2120E001Bad thermistor, triac, SSR or power supply
CANON2020, 2120E030Counter error
CANON2020, 2120E202scanner home position not found
CANON2020, 2120E210lens home position not found
CANON2020, 2120E400ADF problem
CANON2020, 212000-53Sorter communication down
CANON2020, 2120E710main board
CANON3030, 3050E000Fusing unit not heating up
CANON3030, 3050E001Fusing unit overheating
CANON3030, 3050E002Fusing unit not heating up
CANON3030, 3050E003Fusing unit not heating up
CANON3030, 3050E004SSR or exposure lamp board
CANON3030, 3050E010main motor lock, main motor rotation sensor,main board
CANON3030, 3050E022development unit replacement error
CANON3030, 3050E030Counter error
CANON3030, 3050E202scanner home position not found
CANON3030, 3050E204scanner home position not found
CANON3030, 3050E210lens home position not found
CANON3030, 3050E220exposure lamp blown or bad contact
CANON3030, 3050E400ADF control board problem
CANON3030, 3050E401DF paper feed motor lock
CANON3030, 3050E402DF transport error
CANON3030, 3050E403DF paper transport error
CANON3030, 3050E404DF paper exit
CANON3030, 3050E411DF sensors problem
CANON3030, 3050E500Sorter control board
CANON3030, 3050E510Sorter paper transport error
CANON3030, 3050E512Sorter first motor lock
CANON3030, 3050E514Sorter second motor lock
CANON3030, 3050E520Stacker motor overloaded
CANON3030, 3050E530Sorter V motor lock
CANON3030, 3050E531Stapler motor overloaded
CANON3030, 3050E535Sorter V motor lock
CANON3030, 3050E540lateral movement motor lock
CANON3030, 3050E541lateral movement motor lock
CANON3030, 3050E710main board failure
CANON3030, 3050E711main board failure
CANON3030, 3050E712main board failure
CANON3030, 3050E800emergency shut-off relay
CANON3325, 3825E000Fusing unit not heating up
CANON3325, 3825E001Fusing unit overheating
CANON3325, 3825E002Fusing unit not heating up
CANON3325, 3825E003Fusing unit not heating up
CANON3325, 3825E004SSR or exposure lamp board
CANON3325, 3825E010main motor lock, main motor rotation sensor,main board
CANON3325, 3825E022development unit replacement error
CANON3325, 3825E030Counter error
CANON3325, 3825E202scanner home position not found
CANON3325, 3825E204scanner home position not found
CANON3325, 3825E210lens home position not found
CANON3325, 3825E220exposure lamp blown or bad contact
CANON3325, 3825E400ADF control board problem
CANON3325, 3825E401DF paper feed motor lock
CANON3325, 3825E402DF transport error
CANON3325, 3825E403DF paper transport error
CANON3325, 3825E404DF paper exit
CANON3325, 3825E411DF sensors problem
CANON3325, 3825E500Sorter control board
CANON3325, 3825E510Sorter paper transport error
CANON3325, 3825E512Sorter first motor lock
CANON3325, 3825E514Sorter second motor lock
CANON3325, 3825E520Stacker motor overloaded
CANON3325, 3825E530Sorter V motor lock
CANON3325, 3825E531Stapler motor overloaded
CANON3325, 3825E535Sorter V motor lock
CANON3325, 3825E540lateral movement motor lock
CANON3325, 3825E541lateral movement motor lock
CANON3325, 3825E710main board failure
CANON3325, 3825E711main board failure
CANON3325, 3825E712main board failure
CANON3325, 3825E800emergency shut-off relay
CANON4050, 4080E000Fusing unit not heating up
CANON4050, 4080E001Fusing unit overheating
CANON4050, 4080E002Fusing unit not heating up
CANON4050, 4080E003Fusing unit not heating up
CANON4050, 4080E004SSR or exposure lamp board
CANON4050, 4080E010main motor lock, main motor rotation sensor,main board
CANON4050, 4080E022development unit replacement error
CANON4050, 4080E030Counter error
CANON4050, 4080E080color interface problem
CANON4050, 4080E081vertical transport motor overload
CANON4050, 4080E082horizontal transport motor overload
CANON4050, 4080E084color unit sensor
CANON4050, 4080E085color unit position error
CANON4050, 4080E086color unit position error
CANON4050, 4080E089color unit position error
CANON4050, 4080E100laser error
CANON4050, 4080E110polygonal mirror motor not picking up speed
CANON4050, 4080E202scanner home position not found
CANON4050, 4080E204scanner home position not found
CANON4050, 4080E210lens home position not found
CANON4050, 4080E220exposure lamp blown or bad contact
CANON4050, 4080E223color filter motor lock
CANON4050, 4080E240main board
CANON4050, 4080E400ADF control board problem
CANON4050, 4080E401DF paper feed motor lock
CANON4050, 4080E402DF transport error
CANON4050, 4080E403DF paper transport error
CANON4050, 4080E404DF paper exit
CANON4050, 4080E411DF sensors problem
CANON4050, 4080E500Sorter control board
CANON4050, 4080E510Sorter paper transport error
CANON4050, 4080E512Sorter first motor lock
CANON4050, 4080E514Sorter second motor lock
CANON4050, 4080E520Stacker motor overloaded
CANON4050, 4080E530Sorter V motor lock
CANON4050, 4080E531Stapler motor overloaded
CANON4050, 4080E535Sorter V motor lock
CANON4050, 4080E540lateral movement motor lock
CANON4050, 4080E541lateral movement motor lock
CANON4050, 4080E660IC card malfunction
CANON4050, 4080E710main board failure
CANON4050, 4080E711main board failure
CANON4050, 4080E712main board failure
CANON4050, 4080E714main board failure
CANON4050, 4080E800emergency shut-off relay
CANON6030E000Fusing unit not heating up
CANON6030E001Fusing unit overheating
CANON6030E002Fusing unit not heating up
CANON6030E003Fusing unit not heating up
CANON6030E004SSR or exposure lamp board
CANON6030E010main motor lock, main motor rotation sensor,main board
CANON6030E022development unit replacement error
CANON6030E030B&W counter error
CANON6030E031Color counter error
CANON6030E064AC drive board problem
CANON6030E065AC drive board problem
CANON6030E202scanner home position not found
CANON6030E203scanner home position not found
CANON6030E204scanner home position not found
CANON6030E210lens home position not found
CANON6030E212lens home position not found
CANON6030E220exposure lamp blown or bad contact
CANON6030E224blank shutter not working
CANON6030E240main board
CANON6030E244main board to AC drive communication problem
CANON6030E400ADF control board problem
CANON6030E401DF paper feed motor lock
CANON6030E402DF transport error
CANON6030E403DF paper transport error
CANON6030E404DF paper exit
CANON6030E411DF sensors problem
CANON6030E500Sorter control board
CANON6030E510Sorter paper transport error
CANON6030E512Sorter first motor lock
CANON6030E530Stapler motor overloaded
CANON6030E531Stapler motor overloaded
CANON6030E540lateral movement motor lock
CANON6030E541lateral movement motor lock
CANON6030E710main board failure
CANON6030E711main board failure
CANON6030E712paper feed error
CANON6030E716paper tray error
CANON6030E800Auto shut-off relay malfunction
CANON6030E901Paper feed unit electronic board
CANON6030E902Paper feed unit home position error
CANON6050, 6650, 8070, 8570E000Fusing unit not heating up
CANON6050, 6650, 8070, 8570E001Fusing unit overheating
CANON6050, 6650, 8070, 8570E002Fusing unit not heating up
CANON6050, 6650, 8070, 8570E003Fusing unit not heating up
CANON6050, 6650, 8070, 8570E004SSR or exposure lamp board
CANON6050, 6650, 8070, 8570E010main motor lock, main motor rotation sensor,main board
CANON6050, 6650, 8070, 8570E011main drive lock, one of the motors
CANON6050, 6650, 8070, 8570E013used toner transport jammed
CANON6050, 6650, 8070, 8570E014pick-up motor lock
CANON6050, 6650, 8070, 8570E020black toner supply mechanism malfunction
CANON6050, 6650, 8070, 8570E030Counter error
CANON6050, 6650, 8070, 8570E031counter error at one option
CANON6050, 6650, 8070, 8570E050duplex malfunction
CANON6050, 6650, 8070, 8570E051duplex malfunction
CANON6050, 6650, 8070, 8570E202scanner home position not found
CANON6050, 6650, 8070, 8570E203scanner home position not found
CANON6050, 6650, 8070, 8570E204scanner home position not found
CANON6050, 6650, 8070, 8570E210lens home position not found
CANON6050, 6650, 8070, 8570E212lens home position not found
CANON6050, 6650, 8070, 8570E240main board failure
CANON6050, 6650, 8070, 8570E243Operation panel
CANON6050, 6650, 8070, 8570E710power supply error
CANON6050, 6650, 8070, 8570E711power supply error
CANON6050, 6650, 8070, 8570E500Sorter control board
CANON6050, 6650, 8070, 8570E510Sorter paper transport error
CANON6050, 6650, 8070, 8570E512Sorter first motor lock
CANON6050, 6650, 8070, 8570E530Stapler motor overloaded
CANON6050, 6650, 8070, 8570E531Stapler motor overloaded
CANON6050, 6650, 8070, 8570E801thermistor, fusing unit, power supply, main board
CANON6050, 6650, 8070, 8570E802power supply or main board error
CANON6317E000Fusing unit not heating up
CANON6317E001Fusing unit overheating
CANON6317E002Fusing unit not heating up
CANON6317E003Fusing unit not heating up
CANON6317E004SSR or exposure lamp board
CANON6317E010main motor lock, main motor rotation sensor,main board
CANON6317E030counter error
CANON6317E202scanner home position not found
CANON6317E208mirrors home position not found
CANON6317E210lens home position not found
CANON6317E220exposure lamp blown or bad contact
CANON6317E245main board
CANON6317E261Main power supply or Main PCB
CANON6317E400communication lost between copier and ADF
CANON6317E500communication lost between copier and sorter
CANON6317E802Main switch, main power supply
CANONGP200, GP215E000Fusing unit not heating up
CANONGP200, GP215E001Fusing unit overheating
CANONGP200, GP215E002Fusing unit not heating up
CANONGP200, GP215E003Fusing unit not heating up
CANONGP200, GP215E007fusing film damaged or out of position
CANONGP200, GP215E010main motor lock
CANONGP200, GP215E030counter error
CANONGP200, GP215E031counter error at one option
CANONGP200, GP215E032electronic counter error
CANONGP200, GP215E051horizontal registration home position not found
CANONGP200, GP215E064High voltage drive board abnormal output
CANONGP200, GP215E100BD error
CANONGP200, GP215E110polygonal mirror motor not picking up speed
CANONGP200, GP215E190RAM error
CANONGP200, GP215E191communicatio lost between the main board and the power supply
CANONGP200, GP215E202scanner home position not found
CANONGP200, GP215E203scanner home position not found
CANONGP200, GP215E204scanner home position not found
CANONGP200, GP215E210lens home position not found
CANONGP200, GP215E212lens home position not found
CANONGP200, GP215E220exposure lamp blown or bad contact
CANONGP200, GP215E240main board
CANONGP200, GP215E243Operation panel
CANONGP200, GP215E261Main power supply or Main PCB
CANONGP200, GP215E301exposure intensity out of range
CANONGP200, GP215E400ADF control board problem
CANONGP200, GP215E401DF paper feed motor lock
CANONGP200, GP215E402DF transport error
CANONGP200, GP215E403DF paper transport error
CANONGP200, GP215E404DF paper exit
CANONGP200, GP215E411DF sensors problem
CANONGP200, GP215E422copier to DF-F1 communication lost
CANONGP200, GP215E710main board
CANONGP200, GP215E711main board
CANONGP200, GP215E712paper feed error
CANONGP200, GP215E716Paper feed unit error
CANONGP200, GP215E717communication to the copier controller is lost
CANONGP200, GP215E800Auto shut-off relay malfunction
CANONGP200, GP215E803power supply output out of range
CANONGP200, GP215E901Paper feed unit PCB malfunction
Posted by at No comments:
Labels:

Saturday, July 30, 2011

canon imageRunner 3035 3045 3530 3570 45704 canon: canon imageRunner 3035 3045 3530 3570 45704 canon ...

IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->

canon imageRunner 3035 3045 3530 3570 45704 canon: canon imageRunner 3035 3045 3530 3570 45704 canon ...: "UNIVERSAL OFFICE COPIERS (818) 282-8200 Canon Ricoh copier service and repair center LOS ANGELES CA canon imageRunner 3035 3045 3530..."
Posted by at No comments:

Friday, July 29, 2011

Canon Imagerunner IR 7086 7095 7105 error codes e0: Canon Copier imagerunner IR 7086 7095 7105 error c...

IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->

Canon Imagerunner IR 7086 7095 7105 error codes e0: Canon Copier imagerunner IR 7086 7095 7105 error c...: "UNIVERSAL OFFICE COPIERS 818-282-8200 LOS ANGELES CA If the code your looking for is not here just write, or call us. Product : image..."
Posted by at 1 comment:

canon imageRunner 3035 3045 3530 3570 45704 canon: canon imageRunner 3035 3045 3530 3570 45704 canon ...

IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->

canon imageRunner 3035 3045 3530 3570 45704 canon: canon imageRunner 3035 3045 3530 3570 45704 canon ...: "UNIVERSAL OFFICE COPIERS (818) 282-8200 Canon Ricoh copier service and repair center LOS ANGELES CA canon imageRunner 3035 3045 3530..."
Posted by at No comments:

Tuesday, July 19, 2011

Canon Copier imagerunner IR 7086 7095 7105 error code codes e000 001 602 540 732 copiers errors

IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->

UNIVERSAL OFFICE COPIERS
818-282-8200
LOS ANGELES CA

If the code your looking for is not here just write, or call us.


Product : imageRUNNER 7105 / 7095 / 7086
Title : E003-0000 is displayed upon recovery from sleep mode
Error :
E003-0000 is displayed upon recovery from sleep mode

Workaround :
When a machine is in sleep mode and is recovered an error code "E003-0000" was displayed. It is caused during the fixing temperature control at recovery from sleep mode, electrical noise affected the thermistor.

In order to increase the length of time for idle rotation of the drum (by 30 sec) at start-up and prevent electrical noise from affecting the thermistor, make the following selection:
Service mode (Level 2)> COPIER> OPTION> BODY> DRM-IDL = change the setting to '3'

Note: The length of time for idle rotation is being increased by 30 sec. This mode will delay start of the machine by 30 sec.
----------------------------------------------------------------------------------------------
Product : imageRUNNER 7086 imageRUNNER 7095 imageRUNNER  7105
Title : E003
Error :
E003-0000 Error Code can be displayed when the reading of the main thermistor is below 70 deg. C for 2 sec. after it has exceeded 100 deg. C.

Workaround :
1. Although the fixing heater or the temperature-detecting thermistor may be faulty, before replacing these parts, check J508 on the DC controller PCB for poor contact and refit it if necessary.
2. Make the following selections to clear the error code: [Service mode > COPIER > Function > CLEAR > ERR > OK]
-------------------------------------------------------------------------------------------------
Product :
imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title :
E004-0001 Error Code
Error :
E004-0001 Error Code is displayed indicating a short in the main heater circuit.

Workaround :
Check the Main Heater Lamp for burnt (black) ends indicating an arc or short.
Replace the Main Heater Lamp; part number FH7-4719-000. Also check for damaged wiring to the Main Heater Lamp.

Note: to clear the error perform (COPIER>FUNCTION>CLEAR>ERR).
--------------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : Error Code E005-0099
Error :
The error code E005-0099 will not reset in service mode COPIER>FUNCTION>CLEAR>ERR. The E005 indicates the fixing web has run out. In this case the web was only half way used and the fixing web detecting lever was positioned correctly. The end user indicated the error occurred when a print job was paused.

Workaround :
The error cleared after turning the copier on with the finisher off. The copier was turned off, the finisher turned on, then the copier and the machine operated normally.
-----------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title : Error codes E010 and E065
Error :
Machine will alternate between E010 and E065 .

Workaround :
When you are getting this alternating error code of E010 or E065 you must check to see if you are getting 24vdc to main motor and HVDC board .  The simplest way to do this is by going to the HVDC PCB  and check J 721 pins 1 and 2 for 24vdc .  If not there go to J 1723 on Relay PCB and OHMS check pins 1 and 2 for continuity. This is your manual feed tray cover open/closed detection switch.  If good, check pins 5 and 7 that's the front door open/closed detection switch.  If either of the switches has an open it will not power the relay for output to main motor and HVDC pcb.  In our case we had a bad manual feed open/closed detection switch.
---------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : In Service Mode, Getting The Message Waste Toner Container Is Full
Problem :
Only in service mode is the message being displayed, "Waste Toner Container Is Full ".

Error code E013 and E019 do not show up at all in the Error history in service mode. Error Clear and DC CON Clear have been performed in service mode. The Waste Toner Container is empty. Sensor PS 19 (Waste Toner Full sensor) has been replaced. Microswitch 2 (MSW2) the Waste Toner Lock sensor, is operating properly. Connectors J512 and J514 on the DC CON PCB were reseated. In service mode > Copier > Counter > MISC > WST-TNR has been reset to 0 and Copier > Counter > H-DRBL-2 > W-T-PIPE has been reset to 0.





Solution :
In this case, Sensor PS 19 in I/O Mode of service mode was in a state indicating that the Waste Toner Case Is Full and not changing state when the sensor was blocked and then unblocked.

(To check PS 19 in I/O Mode enter service mode level 1 ( * 2 8 * ) > Copier > I/O > DC CON > P003 > bit 7.
A state of 0 for bit 7 indicates the Waste Toner Case Is Not Full.  A state of 1 for bit 7 indicates the Waste Toner Case Is Full.)

In the process of tracing the wiring for sensor PS 19 back to J514 of the DC Controller PCB, it was discovered that the interim connector, J261, in the Waste Toner Bottle Assembly, was unplugged.
After re-connecting the interim connector J261, the message in service mode " Waste Toner Container Is Full ", cleared out; Bit 7 for P003 in I/O Mode was at a state of 0.  Service issue was resolved.

Please refer to the illustration below for the location of the interim connector J261 and sensor PS 19:
--------------------------------------------------------------

Product : imageRUNNER 7086 / 7095 / 7105
Title : E020-0009
Error :
Error code E020-0009 could occur due to toner being packed in the tube from the toner bottle to the developer hopper. This will not allow the toner auger to turn and binds up the buffer motor (M18). You may also notice that the toner bottle will not spin. With the buffer motor removed and power off you will not be able to turn the auger by hand.

Workaround :
Remove the auger from the copier and try to vacuum out the tube to ensure no toner has hardened inside. Reinstall the auger and ensure that you can turn freely by hand.
----------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : Error Code E020-0008
Error :
An error code of E020-0008 is generated when a fault is detected with M22. The symptom in this instance was intermittent. M22 activated in parts check and the technician stated that there seemed to be no mechanical binding in the assembly.

Workaround :
The solution for this instance was to reseat the paddle in the hopper assembly. Upon further inspection of the hopper assembly, it was noticed that the paddle had become dislodged causing it to bind periodically.

------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title :
An E020-0009 is Displayed

Problem :
An E020-0009 is Displayed



Solution :
The developing assembly along with including the buffer unit, buffer motor M18 and the buffer clutch CL1 had been replaced.  In this case, the replacement of the entire hopper assembly resolved the problem.  The part number for the entire hopper assembly is FM2-4063-000.

Note: The service manual lists this code as being for the buffer motor.  Please note the TS4 sensor is part of this circuit.

The TS4 sensor is located in the sub hopper portion of the hopper assembly.  It is recommended to try replacing the TS4 sensor (FK2-0158-000), before replacing the entire hopper assembly.

-----------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Title : E020-0008
Problem :

An E020-0008 is when the toner feed motor is driven and a fault is detected for 3 seconds or more for the (M22) Motor. The error code of E020-0008 still occurred at power up after replacing M22.

Solution :
 In this case, replacing the developer unit resolved the issue.  The part number for the developing assembly is FM2-4872-000.
------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : Intermittent, E025 Error Codes are Occurring
Problem :
E025 is displayed on the Control Panel. This code refers to the Toner Bottle Rotation Motor M23. The code may or may not be a "Hard" failure. The motor M23 as well as the DC Controller were replaced in an attempt to solve the error code to no avail.


Solution :
The Cartridge Motor (MSW8) drive switch was found to be bad. The switch was loading down the voltage to the motor causing it to error out.

MSW8 was replaced to resolve this issue. The part number for the switch is FK2-0384-000.

-----------------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title : E110-0000 when machine goes into high speed rotation.
Error :
E110-0000 when machine goes into high speed rotation.  Machine will also lose the 24vdc and 38 vdc at this time .  If you go into service mode, machine will go to ready and you can check motors, clutches and fans but when you exit you will get an E025-0001.

Workaround :
Replace the separation fan, M13 . Part number is FH6-1942-020.  Found that if we ohmed the blue and red wire going to motor it was aprox 15 ohms a good one should read aproximatley 6k OHMS
--------------------------------------------------------------------------
Product : imageRUNNER 7086/7095/7105
Title : E500-0099
Error :
The machine intermittently will code out to an E500-0099. Sometimes this happens when the machine is powered on, and sometimes it happens while copying/printing.


Workaround :
Try reseating all ARC net components such as cables, terminators, and T-connectors. If the code still occurs, try replacing these components next. If still no solution, replace the ARC net pcbs in the end, part# FM2-4358-000.
----------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Finisher-V1 / Saddle Finisher-V2
Title : E500 Error Code And Suspended Message
Error :
The imageRUNNER will display either an E500 error code or a message of "suspended" on the panel. The problem had been occurring intermittently, about once per week. An E500 error code indicates a communication failure with the Finisher. The system software had been flashed, and the cabling was verified as good.

Workaround :
The solution to the intermittent E500 codes, was to simply reseat the EEPROM on the Finisher Controller. After reseating the EEPROM, the E500 error code, and the "suspended" message did not return.
-------------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Finisher V1 / V2
Perfect Binder A1


Title : Error code E505 0001
Problem :
Unable to clear E505 0001 error code.

Solution :
E505 0001 is used by both the Finisher V1 / V2 and the Perfect Binder A1. First Identify the error code if it is for the Finisher or the Perfect Binder A1, check  the 'L" Location column in Service Mode > COPIER > DISPLAY > ERR.

2 = Finisher. Any other value check Perfect Binder A1. Once identified perform the necessary procedures and or parts replacement for the identified Accessory.

Description of Code
- Finisher error code"E505-0001": A fault exits in the data stored in the EEPROM on the Finisher Controller PCB.
- Perfect Binder error code "E505-0001": The value written to EEPROM and the value read from it do not match.
-----------------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : E602-0013 Error Code
Error :
E602-0013

Workaround :
To resolve this issue, please install system software version 78.02b V2 or higher.


---------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : E602-0413
Error :
E602-0413

Workaround :
When the E602-0413 error occurs try to perform the Hard Drive Clears on each partition.

To perform the HD Clears go into service mode COPIER>FUNCTION>SYSTEM

Select CHK-TYPE and set it to 1 and press ok.
Then select HD-CLEAR and press ok.

Select CHK-TYPE and set it to 2 and press ok.
Then select HD-CLEAR and press ok.

Select CHK-TYPE and set it to 3 and press ok.
Then select HD-CLEAR and press ok.

Select CHK-TYPE and set it to 4 and press ok.
Then select HD-CLEAR and press ok.

After completing this procedure, power cycle the imageRUNNER and reenter any user settings.  If the error still occurs format the Hard Drive with the Service Support Tool and reinstall the System Software.
-------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Title : E732-0010 Only When Using The Feeder
Error :
The imageRUNNER is displaying an error code of E732-0010. The code will only appear when using the Document Feeder, copying off the glass will work fine.  The problem seems to have occurred after the copier was moved.

The sensor initialization was performed for the feeder, but did not solve the problem. All voltages to the Reader Controller and Interface PCB were present. Connections on the Reader Controller and Main Controller were reseated.

The E732-0010 refers to a fault with the reader sync signal detection mechanism.

Workaround :
In this case it was necessary to reseat the communication cables between the Reader Controller and the Interface PCB. Connector J302 and J303 on the Reader Controller and J202 and J205 on the Interface PCB.
-----------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7105 / 7095 / 7095 Printer
Title : Error Codes E840, E732 and E110
Problem :
When the machine is turned on it will display an E840, E732 or E110 error code

Solution :
A poor connection at the machine relay board can cause erratic error codes. Unplug and reseat all of the connectors on the relay pcb. Pay close attention to connectors J7101 and J7104.
-------------------------------------------------------------------------------
Posted by at 56 comments:
Labels:
Subscribe to: Posts (Atom)