IF MY BLOG WAS HELPFUL, PLEASE CLICK/VISIT THE ADD/SPONSOR ON THIS PAGE
THANK YOU SO MUCH FOR YOUR TIME----------->
UNIVERSAL OFFICE COPIERS
818-282-8200
LOS ANGELES CA
If the code your looking for is not here just write, or call us.
Product : imageRUNNER 7105 / 7095 / 7086
Title : E003-0000 is displayed upon recovery from sleep mode
Error :
E003-0000 is displayed upon recovery from sleep mode
Workaround :
When a machine is in sleep mode and is recovered an error code "E003-0000" was displayed. It is caused during the fixing temperature control at recovery from sleep mode, electrical noise affected the thermistor.
In order to increase the length of time for idle rotation of the drum (by 30 sec) at start-up and prevent electrical noise from affecting the thermistor, make the following selection:
Service mode (Level 2)> COPIER> OPTION> BODY> DRM-IDL = change the setting to '3'
Note: The length of time for idle rotation is being increased by 30 sec. This mode will delay start of the machine by 30 sec.
----------------------------------------------------------------------------------------------
Product : imageRUNNER 7086 imageRUNNER 7095 imageRUNNER 7105
Title : E003
Error :
E003-0000 Error Code can be displayed when the reading of the main thermistor is below 70 deg. C for 2 sec. after it has exceeded 100 deg. C.
Workaround :
1. Although the fixing heater or the temperature-detecting thermistor may be faulty, before replacing these parts, check J508 on the DC controller PCB for poor contact and refit it if necessary.
2. Make the following selections to clear the error code: [Service mode > COPIER > Function > CLEAR > ERR > OK]
-------------------------------------------------------------------------------------------------
Product :
imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title :
E004-0001 Error Code
Error :
E004-0001 Error Code is displayed indicating a short in the main heater circuit.
Workaround :
Check the Main Heater Lamp for burnt (black) ends indicating an arc or short.
Replace the Main Heater Lamp; part number FH7-4719-000. Also check for damaged wiring to the Main Heater Lamp.
Note: to clear the error perform (COPIER>FUNCTION>CLEAR>ERR).
--------------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : Error Code E005-0099
Error :
The error code E005-0099 will not reset in service mode COPIER>FUNCTION>CLEAR>ERR. The E005 indicates the fixing web has run out. In this case the web was only half way used and the fixing web detecting lever was positioned correctly. The end user indicated the error occurred when a print job was paused.
Workaround :
The error cleared after turning the copier on with the finisher off. The copier was turned off, the finisher turned on, then the copier and the machine operated normally.
-----------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title : Error codes E010 and E065
Error :
Machine will alternate between E010 and E065 .
Workaround :
When you are getting this alternating error code of E010 or E065 you must check to see if you are getting 24vdc to main motor and HVDC board . The simplest way to do this is by going to the HVDC PCB and check J 721 pins 1 and 2 for 24vdc . If not there go to J 1723 on Relay PCB and OHMS check pins 1 and 2 for continuity. This is your manual feed tray cover open/closed detection switch. If good, check pins 5 and 7 that's the front door open/closed detection switch. If either of the switches has an open it will not power the relay for output to main motor and HVDC pcb. In our case we had a bad manual feed open/closed detection switch.
---------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : In Service Mode, Getting The Message Waste Toner Container Is Full
Problem :
Only in service mode is the message being displayed, "Waste Toner Container Is Full ".
Error code E013 and E019 do not show up at all in the Error history in service mode. Error Clear and DC CON Clear have been performed in service mode. The Waste Toner Container is empty. Sensor PS 19 (Waste Toner Full sensor) has been replaced. Microswitch 2 (MSW2) the Waste Toner Lock sensor, is operating properly. Connectors J512 and J514 on the DC CON PCB were reseated. In service mode > Copier > Counter > MISC > WST-TNR has been reset to 0 and Copier > Counter > H-DRBL-2 > W-T-PIPE has been reset to 0.
Solution :
In this case, Sensor PS 19 in I/O Mode of service mode was in a state indicating that the Waste Toner Case Is Full and not changing state when the sensor was blocked and then unblocked.
(To check PS 19 in I/O Mode enter service mode level 1 ( * 2 8 * ) > Copier > I/O > DC CON > P003 > bit 7.
A state of 0 for bit 7 indicates the Waste Toner Case Is Not Full. A state of 1 for bit 7 indicates the Waste Toner Case Is Full.)
In the process of tracing the wiring for sensor PS 19 back to J514 of the DC Controller PCB, it was discovered that the interim connector, J261, in the Waste Toner Bottle Assembly, was unplugged.
After re-connecting the interim connector J261, the message in service mode " Waste Toner Container Is Full ", cleared out; Bit 7 for P003 in I/O Mode was at a state of 0. Service issue was resolved.
Please refer to the illustration below for the location of the interim connector J261 and sensor PS 19:
--------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : E020-0009
Error :
Error code E020-0009 could occur due to toner being packed in the tube from the toner bottle to the developer hopper. This will not allow the toner auger to turn and binds up the buffer motor (M18). You may also notice that the toner bottle will not spin. With the buffer motor removed and power off you will not be able to turn the auger by hand.
Workaround :
Remove the auger from the copier and try to vacuum out the tube to ensure no toner has hardened inside. Reinstall the auger and ensure that you can turn freely by hand.
----------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : Error Code E020-0008
Error :
An error code of E020-0008 is generated when a fault is detected with M22. The symptom in this instance was intermittent. M22 activated in parts check and the technician stated that there seemed to be no mechanical binding in the assembly.
Workaround :
The solution for this instance was to reseat the paddle in the hopper assembly. Upon further inspection of the hopper assembly, it was noticed that the paddle had become dislodged causing it to bind periodically.
------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title :
An E020-0009 is Displayed
Problem :
An E020-0009 is Displayed
Solution :
The developing assembly along with including the buffer unit, buffer motor M18 and the buffer clutch CL1 had been replaced. In this case, the replacement of the entire hopper assembly resolved the problem. The part number for the entire hopper assembly is FM2-4063-000.
Note: The service manual lists this code as being for the buffer motor. Please note the TS4 sensor is part of this circuit.
The TS4 sensor is located in the sub hopper portion of the hopper assembly. It is recommended to try replacing the TS4 sensor (FK2-0158-000), before replacing the entire hopper assembly.
-----------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Title : E020-0008
Problem :
An E020-0008 is when the toner feed motor is driven and a fault is detected for 3 seconds or more for the (M22) Motor. The error code of E020-0008 still occurred at power up after replacing M22.
Solution :
In this case, replacing the developer unit resolved the issue. The part number for the developing assembly is FM2-4872-000.
------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : Intermittent, E025 Error Codes are Occurring
Problem :
E025 is displayed on the Control Panel. This code refers to the Toner Bottle Rotation Motor M23. The code may or may not be a "Hard" failure. The motor M23 as well as the DC Controller were replaced in an attempt to solve the error code to no avail.
Solution :
The Cartridge Motor (MSW8) drive switch was found to be bad. The switch was loading down the voltage to the motor causing it to error out.
MSW8 was replaced to resolve this issue. The part number for the switch is FK2-0384-000.
-----------------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Title : E110-0000 when machine goes into high speed rotation.
Error :
E110-0000 when machine goes into high speed rotation. Machine will also lose the 24vdc and 38 vdc at this time . If you go into service mode, machine will go to ready and you can check motors, clutches and fans but when you exit you will get an E025-0001.
Workaround :
Replace the separation fan, M13 . Part number is FH6-1942-020. Found that if we ohmed the blue and red wire going to motor it was aprox 15 ohms a good one should read aproximatley 6k OHMS
--------------------------------------------------------------------------
Product : imageRUNNER 7086/7095/7105
Title : E500-0099
Error :
The machine intermittently will code out to an E500-0099. Sometimes this happens when the machine is powered on, and sometimes it happens while copying/printing.
Workaround :
Try reseating all ARC net components such as cables, terminators, and T-connectors. If the code still occurs, try replacing these components next. If still no solution, replace the ARC net pcbs in the end, part# FM2-4358-000.
----------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Finisher-V1 / Saddle Finisher-V2
Title : E500 Error Code And Suspended Message
Error :
The imageRUNNER will display either an E500 error code or a message of "suspended" on the panel. The problem had been occurring intermittently, about once per week. An E500 error code indicates a communication failure with the Finisher. The system software had been flashed, and the cabling was verified as good.
Workaround :
The solution to the intermittent E500 codes, was to simply reseat the EEPROM on the Finisher Controller. After reseating the EEPROM, the E500 error code, and the "suspended" message did not return.
-------------------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7095 Printer / 7086
Finisher V1 / V2
Perfect Binder A1
Title : Error code E505 0001
Problem :
Unable to clear E505 0001 error code.
Solution :
E505 0001 is used by both the Finisher V1 / V2 and the Perfect Binder A1. First Identify the error code if it is for the Finisher or the Perfect Binder A1, check the 'L" Location column in Service Mode > COPIER > DISPLAY > ERR.
2 = Finisher. Any other value check Perfect Binder A1. Once identified perform the necessary procedures and or parts replacement for the identified Accessory.
Description of Code
- Finisher error code"E505-0001": A fault exits in the data stored in the EEPROM on the Finisher Controller PCB.
- Perfect Binder error code "E505-0001": The value written to EEPROM and the value read from it do not match.
-----------------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7105
Title : E602-0013 Error Code
Error :
E602-0013
Workaround :
To resolve this issue, please install system software version 78.02b V2 or higher.
---------------------------------------------------------
Product : imageRUNNER 7086 / 7095 / 7095 Printer / 7105
Title : E602-0413
Error :
E602-0413
Workaround :
When the E602-0413 error occurs try to perform the Hard Drive Clears on each partition.
To perform the HD Clears go into service mode COPIER>FUNCTION>SYSTEM
Select CHK-TYPE and set it to 1 and press ok.
Then select HD-CLEAR and press ok.
Select CHK-TYPE and set it to 2 and press ok.
Then select HD-CLEAR and press ok.
Select CHK-TYPE and set it to 3 and press ok.
Then select HD-CLEAR and press ok.
Select CHK-TYPE and set it to 4 and press ok.
Then select HD-CLEAR and press ok.
After completing this procedure, power cycle the imageRUNNER and reenter any user settings. If the error still occurs format the Hard Drive with the Service Support Tool and reinstall the System Software.
-------------------------------------------------------------
Product : imageRUNNER 7105 / 7095 / 7086
Title : E732-0010 Only When Using The Feeder
Error :
The imageRUNNER is displaying an error code of E732-0010. The code will only appear when using the Document Feeder, copying off the glass will work fine. The problem seems to have occurred after the copier was moved.
The sensor initialization was performed for the feeder, but did not solve the problem. All voltages to the Reader Controller and Interface PCB were present. Connections on the Reader Controller and Main Controller were reseated.
The E732-0010 refers to a fault with the reader sync signal detection mechanism.
Workaround :
In this case it was necessary to reseat the communication cables between the Reader Controller and the Interface PCB. Connector J302 and J303 on the Reader Controller and J202 and J205 on the Interface PCB.
-----------------------------------------------------------------------------
Product : imageRUNNER 7086 / 7105 / 7095 / 7095 Printer
Title : Error Codes E840, E732 and E110
Problem :
When the machine is turned on it will display an E840, E732 or E110 error code
Solution :
A poor connection at the machine relay board can cause erratic error codes. Unplug and reseat all of the connectors on the relay pcb. Pay close attention to connectors J7101 and J7104.
-------------------------------------------------------------------------------
IF you have a Canon copier that has a problem, error codes jam code, post your error, and we will try our best to help you out, FREEEEEEE
ReplyDeleteunlike canon usa $150 hour... if you have canon copiers color copiers, small desktop copy machine, large clc copy machines, canon fax machines, DR scanners, scanner, and Printer, printers... with error codes we can help
This one has been a doozy for us. IR 7105. Error code E000540-8001
ReplyDeleteCode states the finisher output tray cannot move up and down. Entire finisher was swapped out, plus all controller boards. Error persists.
Been 6 weeks since code appeared. Help?? Pretty Please!
Did you check your wall outlet to see if you have the correct voltage and amp. After that clear error from service mode? Also try D-con clear but make sure you have the printouts to put the settings back.
ReplyDeleteBut before all that, when u turn it on, you get error right away? Or you hear noise or any movement from the tray?
Yes on Voltage and Amp. Checked and correct. Errors were cleared but problem persists. Upon startup, screen reports error and offers limited functionality mode (which still doesn't work). Finisher never makes a peep or movement.
ReplyDeleteI have canon ir7095. It is giving the message door open. I have checked the dc board, power supply and switch. All these are ok. But still the problem is not going away.
ReplyDeleteWhat happens when you look in I/O mode, does the switch change state?
DeleteHave you tried performing a DCON clear
make sure you print P-print before clearing
If in I/O mode the signal does not change, have you checked the signal from the switch to the dc controller connector to verify it is changing state?
If it does not , have you changed the switch or cut wire ties from the switch to the DC controller connector?
If the signal does change at the connector, have you swapped / replaced the DC controller for effect?
If you are missing 24v to the switch, could be a power supply issue.
E 19 how to reset this...canon 7086
ReplyDeleteI was low on toner so I pulled out the cartridge and tap the remaining toner to the front of the housing replaced it and set my print parameters to toner saver ON. Then after 150 or so impressions this error code E19 stopped the imagesetter/copier.
Deleteerror 804-001 what's problem
ReplyDeleteERROR E000-00009 IN IR CANON7086,HOW CAN ROMOVE IT
ReplyDeleteI am getting the error code E00069-0000 and E00020-0002 and E00020-0010.
ReplyDeleteI tried to pull the wall socket and waited for sometime and started. It works for a while. then goes back to the error codes.
Workaround :
DeleteIf E069 code is occurring, but "clears out" when J 733 of the HVT-DC pcb is unplugged, one thing to inspect is the condition of the black mylar shields for the Upper and Lower Pre-Transfer Guides.
If the black mylar shields are wrinkled, ripped, torn or frayed, arcing of the Transfer Guide bias may occur, which will cause the E069 code.
Try covering the Upper and Lower Pre-Transfer Guides with electrical tape, then check the copier operation with J 733 of the HVT-DC pcb connected.
If E069 code does not occur the Upper and Lower Pre-Transfer Guides need to be replaced.
This comment has been removed by the author.
DeleteI have canon ir 7095, that time i start my machine. The finisher exit tray "A" go down,the other question my machine ir 8500,after make a 4000 or 5000 copy after print coming lighting with every copy. After shutdown machine for 10 minutes copy came good.
DeleteI have iR7105 and it gives me a black soiled print - print is is good condition but with background can you suggest
ReplyDeleteit can be the corona assy's
DeleteE000197-0000 what's problem ir7105
ReplyDeleteProblem :
DeleteE197 error code during power on.
Solution :
The registration bias lead may come loose and cause the error code E197 to appear during boot up.
1) Pull the seperation / transfer corona unit out.
2) Inspect the bias cable located to the right of the sep/trans assembly holder in the rear of the transport assembly.
3) Tighten and adjust tube if needed as outlined in TP06 121 confirm there is no short between the screw and cable.
Workaround :
DeleteThe E197 can be cause by a pinched wire between the Video PCB and the Relay PCB. Check the wiring and cut wire ties coming from connector J1405 on the Video PCB. The part number for the harness is FM2-5427-000.
Solution :
DeleteFound the fuser bias tab shorted to the fixing frame assembly due to a broken heater holder.
FB5-6944-000 (Holder, Heater)
FB5-6951-000 (Terminal, Bias)
E733 0010 CODE
ReplyDeleteProblem :
DeleteDuring or after the boot-up process, the machine will display an E733 or E713 error code.
Solution :
If there is a bind in the fuser drive, a dc voltage drop can cause an E733 or E713 at boot up. Check the fuser roller bearings and the fuser drive for wear.
tinaNovember 22, 2014 at 5:56 AM
DeleteError :
E733 Error occurs at start up.
Workaround :
If the E733 Error occurs, check the wiring to sensor PS9 in the Fixing/Feeding Frame Assembly. Replace the wiring to PS9 if it is damaged.
This comment has been removed by the author.
ReplyDelete0197 error when machine startup
ReplyDeleteBased on what I found and your previous post I would look at the fused unit, clear the code turn copier off, pull the fused unit out and turn it on while the unit is out, see if the code comes back, if not push unit back in close door and if code comes back on than you know it's possible that it's cause something on the unit, who's would be bias.. Fused..etc
Deleteis it possible that in 0197 error..... HVT is not work
ReplyDeleteError :
DeleteE197 error.
Workaround :
The E197 can be cause by a pinched wire between the Video PCB and the Relay PCB. Check the wiring and cut wire ties coming from connector J1405 on the Video PCB. The part number for the harness is FM2-5427-000.
Problem :
DeleteE197 error code during power on.
Solution :
The registration bias lead may come loose and cause the error code E197 to appear during boot up.
1) Pull the seperation / transfer corona unit out.
2) Inspect the bias cable located to the right of the sep/trans assembly holder in the rear of the transport assembly.
3) Tighten and adjust tube if needed as. confirm there is no short between the screw and cable.
Error :
DeleteE197 error is generated shortly after rebuilding the fixing assembly.
Workaround :
Although this code refers to a communication error with the laser scanner motor (M4), it has been found that a fixing bias short will cause the E197.
If the fixing unit was recently rebuilt, check to make sure that the orientation of the fixing bushings and bearings are in it's correct position.
Error :
DeleteThe copier is displaying an error code of E197. The copier may also indicate "Suspended" on the display. A check of the Fixing temperature in display, reveals the Fixing Unit temperature is dropping.
Workaround :
Check I/O mode for proper detection of the Duplex Unit (Through path tray detection @ P005 bit 13). It should indicate a "1" when the Duplex tray is in the copier. (The Service Manual and the Technical Reference guide states it should indicate "0".) This is incorrect. Also, Check P005 bit 14, for the Fixing Unit Transport Release Lever Sensor. It should indicate "0" when locked into position, "1" when released.
The E197 indicates a problem with the Laser Scanner Motor communication. It has been found that a poor connection of the Video PCB, or a problem in the related wiring may cause one or both of the aforementioned problems.
Video PCB FM2-4354-000
Conversion Cable FM2-5428-020
ReplyDeleteProblem :
The machine generates an E197 error code. This code refers to a communication error with the laser scanner motor (M4). In an attempt to resolve the issue; the laser assembly, main controller, video pcb, dc controller and all coronas were replaced. The machine would generate this code when almost up to full temperature during potential control.
Solution :
Found the fuser bias tab shorted to the fixing frame assembly due to a broken heater holder.
FB5-6944-000 (Holder, Heater)
FB5-6951-000 (Terminal, Bias)
error code E000227-0001 on iR3245n mfp .what can i do to remove this code?show me the steps.
ReplyDeletecould you show the steps by video for canon IR3245n mfp
ReplyDeleteerror code E000225-0001 on iR7105 .what can i do to remove this code?show me the steps.
ReplyDeleteFix code 000225 001 canon 7095
Deleteopier iR7095 has a problem. The problem that manifests when opening and closing the front door or the manual feeder, the machine remains blocked if the doors are closed. After a while, the machine ejects error E733 - 0001. The only way that the device is up and running to get off and on again. While the door is closed, the device is operating normally. Any solutions or advice what we should check?
ReplyDeleteSir this error is with me can you help me
Deleteir7105... error ...E000566-8001.
ReplyDeleteHelp...
Urgent..
This comment has been removed by the author.
ReplyDeletecanon 7095 E000583 8002
ReplyDeleteHelp.
canon 7095 E000583 8002
ReplyDeleteHelp.
i got a code of 5100 on my Canon MX432 printer/fax/copier. What does this mean? I was trying to do a head alignment.
ReplyDeleteE000001-0010 error in iR7095, what is the problem, please tell me solution
ReplyDeleteir canan 1095 err000732 0001 how cler
ReplyDeleteYour copier error e000732 0001.
DeleteCheck machine backside all plug
ir canan 1095 err000225 0001 how cler
ReplyDeleteE00197
ReplyDeleteCannon iR 7105 Copier Error code
ReplyDeleteE000748-4910 plz tell me solution
Canon ir 7086 copier error code E000850 0000
ReplyDeletePlz send me solution
copying machine http://bit.ly/fotokopimakinesi
ReplyDeletecanon ir 7105 paper jam error ps27 sensor error what is the problem, please tell me solution
ReplyDeleteI would like to thank you for the efforts you have made in writing this article and i am hoping the same best work from you in the future as well. Are you not able to fix the problem with the Canon Printer? Just follow the steps which are mention on the blog to Resolve Canon Hard Disk Error Code E602 issue. Thanks!
ReplyDeleteSir ir canon 7095 machine in start for error not display is wait after 2 hrs on of , on of, afer start machine pz solved problem sir
ReplyDeletesir,
ReplyDeletecanon 7105 the machine is running in five or ten paper copying. then the machine paper not come, the machine is printing wait the paper is not come machine is hanging please solve the problem
Thank you for the post. It is really informative.
ReplyDeletewhat is opening balance equity
how to reprint a check in quickbooks
quickbooks error 6123